TEK Need help on making a bong that works.

[LeadCenobite]

I know some people were giving me ideas before but I'm not sure what posts those were in. Can anyone describe how to make a water bong out of house-hold materials? Details would be great too. I'm not experienced at making these things so any help is good. Pictures would be nice too so I can see if mine looks alike. Also I only have one bowl cuz I only have one pipe on me right now so I hope I dont need to wreck it or anything. Also how do u clean screens properly? Mine always turn black..wonderin if this ruins the quality of smoke or not. I only have that one screen and i wanna get high tomorrow. My bong shop is closed for a month...<cries> Also how baked can bongs get you? I remember the first time i smoke up..I had 3 hits from a huge bong..it was the greatest high ever. 3 hits seems really low to me but trust me I got so smashed. It takes alot long in my pipe to feel that effect

[dr ACE]

get a small empty plastic bottle and burn or make a hole to fit your pipe in an old pen works or any tubing you have,then just get a socket and a picece of hose and that usualy works well for me,but if you can afford it get a glass bong cause they are awsome..

[club222]

Here's how I made my home-made one. I got one of those clear tubes that
you can use to hold posters and stuff once they are rolled up. Then I
got a BIC pen and took out the ink cartridge and the little cap at the
end, so you just have a straight pipe. Then put a hole in the side of
the bong a couple inches from the bottom. Make the hole very small to
start with and then make it bigger and bigger until you have to jam the
pen through there. You want this part to be air tight. After I got mine
in I still put an epoxy around it to better help seal it. Now for the
bowl, you can use a socket like some people do, or you can use a bottle
cap from a soda bottle. I drilled a hole in the top of the bottle cap
just a tad bigger than the pen that is sticking out of the bong. After
you get the hole in your bottle cap and test fit it, wrap it in
aluminum foil so that the flame won't burn the plastic when you light
it. Cut out the aluminum foil where the hole for the pen is so the
smoke can still travel down the pen. After it's all wrapped in aluminum
foil, I put the bottle cap upside down on the table and then layed
another piece of aluminum foil over it and pushed it down a little bit
to create a bowl. Then I took a razor blade and poked a couple small
holes in it to make the screen. You can skip that part though since you
have a screen, Just smash it down into the bottle cap. Next put the
bottle cap back onto the pen. I used epoxy here also to help seal it.
The pen should go down into the bong at an angle. On the opposite side
of the bong that the bowl is, the side that will be closest to you, cut
a hole for your carb.



That's it. It's really not hard at all.

[cwatt]

save up 10 bucks and find someone to buy a plastic bong for you if your not 18. if not then a 2 liter of soda works nice. burn a whole towards the bottom so your bowl will fit in.you will need a downstem, u can use your pipe or bowl as a downstem or make one just using a pen or tube.

[kj_hash420]

do what dr ace posted, that is how i make all of my bongs, and sockets hit hard

[GreyApple]

heres what i do, I take a regular bottle and burn a hole in it with my ciggerite and then take a hollow out pin and connect a folie to it but to make a good size bowl i cut a square out of a pop can and roll in in to a cone and place the folie in that and of course poke my holes in the folie and then load that bowl up and smoke smoke smoke

[Cakes]

The cig for a heat source is a great idea as long as I don't have to smoke that cig afterwards .

got one of those clear tubes that SWIY can use to hold posters and stuff once they are rolled up

beavisnbutthead.gif

maybe even wrap it in one of those posters?

[jkolt89]

Swiy can always make a simple, effective bong in a couple of minutes with a plastic container, a stem and bowl, and some silicone. Finding a good stem and bowl may not always be easy, depending on where you live. Swiy can make a crude stem and bowl from Hardware parts--namely, a length of copper tubing and a brass fitting glued together. When in doubt of supplies to use, browse a hardware store.

                      _|  |_  <---"mouthpiece"
                     /        \
                    /          \
                   /            \     <---chamber
                  |              |    
                  |              |  \  /  <---bowl
      "carb"--->   O       |  / /
                  |              | / /  <---stem
                  |               / /
                  |              / /
                  |              |
                  |              |
                   \_____   /

[See bong diagram from above....] Anyway, cut a hole about midway up the container (allow for the stem's angle), and shove in the stem. Seal it up with generous amounts of silicone and let dry. Poke a small hole onthe side opposite the stem (about 1/4", below the level of the bowl) for the carb. The silicone makes an airtight seal--very important--so you don't waste lung power.